How To Flash Kata V4 Firmware File [Stock ROM]

Today we have a good new News for Kata V4 users, Now you can download and install the Kata V4 Firmware. If you are searching stock Firmware for Kata V4 So you are in right place. Here we will complete guide you how to Install Kata V4 Firmware via SP Flash Tool.

Kata V4 Firmware

 

This article contains the Kata V4 Firmware. That will allow you to recover your Kata V4 mobile into its initial Factory state. Additionally, you can use the file to change your phone to the newest version. You’ll find these below files useful if you have used the flashed customized builds on the device. brick your device, change your device and also come back that device to the factory state.

The Benefit Of Kata V4 Firmware:

  • Flash Stock To Unbrick your Kata V4
  • Flash Stock ROM to solve the boot loop issue
  • Update and Downgrade Kata V4
  • Unroot or Fix Bugs on the phone
  • To solve the lag or stutter on Kata V4
  • By flashing Stock ROM, you can fix software issues.
  • Revert back to stock to get your warranty.

Kata V4 Firmware Details:

  • Gapps File: Included
  • Device Supported: Kata V4
  • Tool Supported: SP Flash Tool
  • Processor: MediaTek –MT6580
  • Os: Android 5.1 Lollipop

Kata_V4_MT6580_5.1.rar

Pre-Requirements To Flash Kata V4 Firmware:

Take a Backup:

Kata V4 Flashing Tool:

We will use Sp Flash Tool to flash Kata V4 firmware. This tool is very efficient. Follow the step by step procedure to use One Click Unbrick Tool and unbrick your Kata V4.

SP Flash Tool which is also known as the Smart Phone Flash Tool is a cross-platform application. We use the SP flash tool for Flash custom recovery, flash Stock Rom and to fix the hard brick device. This is a very simple tool SP flash tool is used on Mediatek devices. This allows you to flash stock firmware on Mediatek smartphones and Tablets only. It will not support the devices having chipsets other than MediaTek.

Kata V4 Driver:

How to install Firmware on Kata V4:

  1. Extract And Run SP flash tool.
  2. Install MTK android USB drivers.
  3. Then download Kata V4 Firmware.
  4. switch off your mobile remove the battery (if removable) reinsert the battery and plug the USB cable in charging socket.
  5. Now open SP flash tool.exe.
  6. When SP flash tool open, go to download button in SP flash tool.
  7. In the download tab, click on the scatter load button.
  8. After locating the scatter tab, click on the download button.
  9. Now connect your smartphone with a USB cable and press volume up or volume down key for easy detection (remove and reinsert your phone battery if it is removable)
  10. When flashing is completed, a green ring will appear in SP flash tool.
  11. Close SP flash tool on your computer and unplug the phone.
  12. Power on the phone and enjoy.
  13. After the flashing process starts, it might take up to 5–10 minutes. So keep patience and wait.

Follow Detailed Instruction Kata V4 Firmware Flashing With Sp Flash Tool

Disclaimer:

  • Please Read and understand the Full Guide Before Flashing Kata V4 Stock Rom.
  • Use these instructions at your own risk. We will not be responsible for everything that happens to you or your device. resulting from the use of information in this guide.
  • Make sure that the USB drivers for your device are installed on the computer.
  • Your smartphone must have a 70–80% charge.
  • Make a backup copy of important data. such as call logs, SMS, and other data, it is to if something goes wrong, your data is not affected

Don’t flash another preloader and DSP_BL blocks! It is always dangerous! On some models of phones, you will have a brick even if you download these blocks read from a phone which you own! Always remove from them marks in SPFT! ALWAYS have a working backup of your original ROM before you flash a new unknown ROM.

Comments are closed.

This website uses cookies to improve your experience. We'll assume you're ok with this, but you can opt-out if you wish. Accept Read More